Sharing helps others too!

70

shares

• Share

Okay, is one of my favorite projects!!!

It’s junky, rusty, reclaimed, burlapy {now days burlapy is a word} and it makes me smile! 🙂

Blogger Saw Blade sign!

This post contains affiliate links. I will make a commission for your purchase at no extra cost to you. This helps me maintain the website.  Thank you for your support. Think of it as a friend letting you know where I found a product I use, love or want.  Click here to read my full disclosure policy.

Plus, I spent a total of $6.50.

Hum, I guess the photo above could have been rotated!  It’s not like the saw blade has a top or bottom in the photo.

Oh, well!  I spent $6.50 for the perfect saw blade.  There were others at the restore, but none as perfect as this one.  I wanted rusty with large teeth {the sharp pointy things around the edge} and most important a round hole.

Some saw blades have a diamond shape, I needed it to spin freely and easy on a bolt.  This one is a 10-inch blade.

My inspiration

Now for the idea.  I was inspired by a round slide rule that was my dad’s and now sits on my desk.  Daddy used it for navigation when flying, but other than that I don’t have a clue how it works!!  But I love looking at it and turning it.  If anyone knows anything about it, please let me know.

I also remember vintage shop signs that would have a disk inside than you could spin around to say open, closed, or out to lunch.

How to make a spinning sign

List of supplies

2 pieces 12 inches long from 10-inch wide board.  {Actually it’s 9 1/4 inches wide}
2 pieces 9 /14 inches long of 1/2 square trim
10- inch Saw Blade or a piece of 1/4 inch plywood cut in a circle
Miter saw  {this is the one Mike gave me for my birthday}
Jigsaw
Drill with a 1/4 inch bit, a smaller bit {I used a 3/16 bit} a countersink bit
Clamps
Quality wood glue
Chalk marker
Burlap ribbon or strips of burlap 2-inches wide
Craft glue
One bolt 1/4 by 1 3/4 inches with nut and two washers.
Router with keyhole bit
Paint and paintbrushes

Steps I used

I used scrap wood from a broken cabinet.  First, I cut the wood to 12 inches.  Next, I measured where to place the center hole so the saw blade would hang out about an inch or so.  I drilled a 1/4 inch hole through the two boards.  I countersink the back hole to fit the nut and still hang flush on the wall.

Now, I need a small rectangle to “change” my sign.  Above shows a simple and quick way to get a cut using the jigsaw.

Now back to the rusty saw blade.  I drew lines with chalk like a pie.

Hum, I’m getting hungry!

Anyway,

I lined the blade up with the center holes, making a sandwich.

I must be really hungry!

Then drew the outline of the square into the saw blade.  You can see I also sanded back most of the black only to find white paint that I again sanded.  So, I used my favorite tea and ironed vinegar technique to age the wood.

Next, I hand wrote six different tasks that I commonly do as a home DIY blogger using a chalk marker.  I thought about stenciling the lettering, but now I like the handwritten tasks.

Note, you can see I added 1/4 pieces of wood along the two sides as spacers.  Or you could think of it as the cheese along the sides of the sandwich!  These were glued in place.

On the back, I used a keyhole router bit to make a hole to easily hang the sign.  This type of hole also helps hold the sign on the wall well when it spins.  If you don’t have a router, this bit is a great reason to buy one!

Assemble the pieces

I assembled the boards using wood glue.  Adding the bolt holds everything in place.  Thread the bolt through the front, add a washer.  Then add the saw blade and the other washer.  Then thread through the back board.  Add the nut.

Sandwiches, cheese, pie, nuts…I’m really getting hungry.

To finish I used the freezer paper method to transfer lettering printed with my computer on the front.  You can read how this method works here.

I did buy freezer paper on Amazon that’s 8 ½ by 11 sheets!  Woot!  No cutting up the roll and trying to get the paper to lay flat in the printer.

I hung my blogger saw blade sign in the craft room along with a soda crate and an old rusty spring from a bench.

I almost forgot the best part!  The burlap!  I first thought I would nail additional trim along the sides and top to “hide the cheese!”  But I wanted it to remain simple and rustic, so I glued on a strip of burlap.

Here’s a close up of my tasks.  All of them I do regularly!!! 🙂

In the workshop, covered with saw dust, sleeping at the computer, redoing the mantel…again, taking photos while balancing on a ladder and writing about the DIY that went wrong %&?@!

Don’t get me wrong…I love blogging AND REALLY love creating.

I love my blogger saw blade sign!  Love DIY and I love blogging! <3

Since this post, I made a spinning chalkboard sign.

I’m getting dizzy!!! 🙂

✕

Join the newsletter

Subscribe to get our DIY HelpLetter each Thursday. Plus grab your Interior Decorating Ideas e-book.

Success! Now check your email and click to confirm your subscription and grab your Interior Decorating Ideas download e-book!